Coupler Nuts CNW and ATS C coupler nuts are used to connect one threaded rod to another and connect to anchor bolts within the Strong Rod Anchor Tiedown System for shearwall overturning restraint Couplers are available in same rod size each end as well as reducing couplers to allow for stepping of rod sizes up the rod run
ATS C coupler nuts are used to connect one threaded rod to another and connect to anchor bolts within the strong rod anchor tie down system for shearwall overturning restraint ATS C coupling nuts exceed the tensile capacity of the corresponding standard ASTM A307 strong rod
Simpson Strong Tie CNW5 8 5 8 quot Coupler Nut w Witness Hole Nuts and Couplers Simpson Strong Tie 174 coupler nuts are a tested and load rated method to join threaded rod and anchor bolts The Witness Hole 174 in each nut provides a means to verify when rods are properly installed The positive stop feature helps ensure even threading into each end of the nut
Titen HD 174 Rod Coupler The Titen HD 174 rod coupler screw anchor is designed to be used in conjunction with a single or multi story continuous rod tie down system This anchor provides a fast and simple way to attach threaded rod to a concrete stem wall or thickened slab footing
Electrogalvanized threaded rod coupler imperial Material composition Carbon steel ASTM A563 Grade A Surface finish Electro galvanized for dry indoor use only More technical data Review Average rating of 5 Number of reviews 0 Be the first to write a review
Simpson Strong Tie CNW5 8 5 8 quot Coupler Nut w Witness Hole Simpson Strong Tie CNW5 8 5 8 quot Coupler Nut w Witness Hole 44315248818 CNW Coupler Nuts are used to connect one threaded rod to another or to an anchor bolt within the Strong Rod ATS system quot Witness quot holes in the nut allow a way to visibly verify when rods are properly installed
all thread rod witness holes coupler nut all thread rod to 2nd floor not provided floor sheathing field drill shim amp hdq8 holdown pre installed 11 4 1 2 quot sw2 min 4 1 2 quot min to accept cutout subfloor bearing plates 2 3 5x6 5x3 8 3 2x4 squash blocks min or solid blocking all thread rod top plates for field drill dbl all thread rod to
Simpson Strong Tie CNW5 8 1 2 5 8 quot to 1 2 quot Coupler Nut w Witness Hole Nuts and Couplers Simpson Strong Tie 174 coupler nuts are a tested and load rated method to join threaded rod and anchor bolts The Witness Hole 174 in each nut provides a means to verify when rods are properly installed The positive stop feature helps ensure even threading into each
8 Install the threaded rod into the CNW coupler nut or the threaded head of the Titen HD rod coupler 9 Attach the rod to the top of the beam with a nut and the appropriate bearing plate chosen from the table Install hollow column anchorage after the concrete pour eliminating the need to determine the precise
National Hardware S836 395 N182 709 N347 070 Stanley Threaded Rod Coupler 1 2 Inch 13 Tpi Zinc Plated Steel SKU VPVC 1840 UPC 033923836395 Threaded rod coupling nuts zinc plated steel coarse boxed bulk size ins Thread 1 2 13 Used for joining threaded rods
A coupling nut is another possibility for joining an addition al threaded section to the embedded rod see Figure 5 The coupling nut is a larger diameter than the rods which may re quire the base plate holes to be enlarged Figure 4 Welded anchor rod splice Figure 5 Anchor rod extension using coupling nut
CNW3 8 Coupler Nut Simpson Strong Tie coupler nuts are a tested and load rated method to join threaded rod and anchor bolts The Witness Hole 174 in each nut provides a means to verify when rods are properly installed The positive stop feature helps ensure even threading into each end of the nut The CNW exceeds the specified minimum tensile capacity of corresponding
SIMPSON STRONG TIE THD50934RC Titen HD Rod Coupler 1 2 quot x 9 3 4 quot 20ct 158 43 FOR SALE Simpson Strong Tie THD50934RC Titen HD
Simpson Strong Tie CNW1 7 8 coupling nuts are a tested and load rated method to join 1 quot threaded rod or anchor bolts to 7 8 quot rod extensions The quot witness quot holes in the nut provide a means to visually verify when rods are properly installed The positive stop feature helps ensure even threading into each end of the nut
3 Simpson Strong Tie high strength Strong Rod and high strength fully threaded rod is based on minimum Fy 635 MPa and Fu 830 MPa 4 Simpson Strong Tie ATS SRxH150 super high strength Strong Rod is based on minimum Fy 900 MPa and Fu 1035GPa 5 In accordance with ANSI ASME B1 1 thread specification for threded rod must be UNC Class
threaded rod Contact Simpson Strong Tie for other coupler nut sizes Finish Zinc Plated Installation Tighten the two rods until each all thread rod is visible in the Witness hole Any portion of thread visible in the witness hole is a correct installation Standard CNW for use with non hot dip galvanized all thread rod only
Simpson Strong Tie 174 coupler nuts are a tested and load rated method to join threaded rod and anchor bolts The Witness 174 hole in each nut provides a means to verify when rods are properly installed The positive stop feature helps ensure even threading into each end of the nut
The Titen HD rod coupler installs with regular or hammer drill ANSI size bits and standard sockets Compatible with threaded rods in 3 8 quot and 1 2 quot diameters Material Carbon steel Finish Zinc plated Installation Drill a hole using the specified diameter carbide bit into the base material to a depth of at least 1 2 quot deeper than the required embedment
adhesive anchors and threaded rod or coil strap Rod Configuration This connection utilizes the Simpson Strong Tie 174 Titen HD 174 Rod Coupler or Epoxy Tie SET anchoring epoxy for concrete anchorage A coupler nut threaded rod and a bearing plate and nut complete the connection to the beam at the top of the column INsTALLATIoN
1 2 quot Coupler Nut w Witness Hole Simpson Strong Tie CNW5 8 1 2 5 8 quot to CNW Coupler Nuts are used to connect one threaded rod to another or to an anchor bolt within the Strong Rod ATS system quot Witness quot holes in the nut allow a way to visibly verify when rods are properly installed 5 8 quot to 1 2 quot Coupler Nut w Witness Hole Simpson Strong Tie CNW5 8
30 9 2008 nbsp 0183 32 Titen HD 174 Rod Coupler The Titen HD 174 rod coupler is a threaded rod anchor for concrete and is designed to accept 3 8 and 1 2 threaded rod The threads of the Titen HD 174 rod coupler concrete anchor are patented and are serrated to
22 4 2021 nbsp 0183 32 Simpson Strong Tie coupler nuts are a tested and load rated method to join threaded rod and anchor bolts The Witness Hole in each nut provides a means to verify when rods are properly installed The positive stop feature helps ensure even threading into each end of the nut The CNW exceeds the specified minimum tensile capacity of corresponding ASTM
Titen HD rod coupler screw anchors are designed to create an anchor point for threaded rod in single or multi story rod tie down systems All Titen HD screw anchors feature a patented thread design with serrated cutting teeth for easy installation Drill Bit Size 3 8 quot Finish Spec Zinc Plated Carbon SteelHead Type Hex
On HDG PABs chase the threads to use standard nuts or couplers or use overtapped products in accordance with ASTM A563 for example Simpson Strong Tie 174 NUT8 OST NUT8 OST CNW8 OST CNW8 OST Some OST couplers are typically oversized on one end of the coupler nut only and will be marked with an O on oversized side Couplers may be
The Simpson Strong Tie Crimp Drive anchor is an easy to install expansion anchor for use in concrete and grout filled block The pre formed curvature along the shaft creates an expansion mechanism that secures the anchor in place and eliminates the need for a secondary tightening procedure The Rod Coupler head is designed for 3 8
Simpson Strong Tie coupler nuts are a tested and load rated method to join threaded rod and anchor bolts Witness holes in the nut provide a means to verify when rods are properly installed The positive stop feature helps ensure even threading into each end of the nut CNW s meet and exceed the tensile capacity of corresponding ASTM A36 bolts and threa
The Titen HD Rod Coupler is designed to be used in conjunction with a single or multi story rod tiedown system This anchor provides a fast and simple way to attach threaded rod to a concrete stem wall or thickened slab footing Unlike adhesive anchors the installation requires no special tools cure time or secondary setting process just drill a hole and drive the anchor
Simpson Strong Tie CNW1 2 instruction manual and user guide Simpson Strong Tie 1 2 in Witness Coupler Nut CNW1 2202092467
All ATS couplers available with over sized threads on one side for use with HDG rod ATS–Cxx–OST ATS–HSCxx–OST and ATS–HSSCxx–OST All CNW and HSCNW couplers are zinc plated Couplers in the 1 3 4″ and 2″ series may be cylindrical ATS–HSC couplers are used for both standard–strength and high–strength rods in 1 1 2″ 1 3 4″ and 2″ diameters
nVent LENTON weldable couplers provide a quick and easy solution for connecting reinforcing steel bar rebar to structural steel sections or plates The coupler is internally taper threaded on one end with the other end or exterior surface prepared for welding C2 C3J Weldable Half Coupler C2 C3J Weldable Half Coupler for Nuclear Applications